Telecommunications Techniques Corporation 41440A Interface
Hersteller:
Kein Bild verfügbar!
Vielleicht kannst du ein Bild für
Telecommunications Techniques Corporation 41440A
hochladen ?
Wenn du andere Handbücher für ein
Telecommunications Techniques Corporation 41440A hast,
kannst du die Dateien hier hochladen .
Modell:
41440A
Datum:
1995
Kategorie:
Gruppe:
Beschreibung:
T1/FT1 DATA INTERFACE
Information
The T1/FT1 Interface Module can do all of the following:
• Test Nx64 kb/s and Nx56 kb/s contiguous or noncontiguous
fractional T1 or full T1 circuits.
• Verify and troubleshoot Fractional T1 configurations.
• T1/FT1 drop and insert capability that allows Nx56 kb/s or
Nx64 kb/s bit error analysis without disrupting traffic on
the remaining timeslots.
• V.54 support for sending in-band loopbacks over a FT1
bandwidth.
• ANSI T1.403 PRM support for reporting on far-end status
/FIREBERD 6000 only). Requires Option 6009.
® Auto-scan and auto-coofigure to any Fractional T1 circuit.
• T1 level and simplex current measurement.
• Timing and pattern slips analysis.
• CSU and smartjack (facility) loopback tests using built-in
in-band or out-of-band ESF Data Link loop codes.
• Responds to CSU loop up and loop down codes.
• Transmits and monitors voice and ABCD signaling bits.
• Generates logic, Bipolar Violations (BPVs), and frame errors.
• Detects the presence of B8ZS, framed patterns, Yellow
Alarm, Excess Zeros Alarm, AIS and ones density violation
alarm conditions.
• Monitors T1 signals using BPVs, frame errors, and CRC errors.
• Measures and generates jitter with FIREBERD 6000,
Dokumenttyp:
Bedienungsanleitung
Seiten:
76
Größe:
2.83 Mbytes (2970553 Bytes)
Sprache:
english
Revision:
G
Dokument-ID:
50-11732-01
Datum:
1995 06 01
Qualität:
Gescanntes Dokument, alles ist lesbar.
Upload Datum:
2017 01 09
MD5:
3a9d7fb5ce4de35ae2515a667d7b18d4
Downloads:
364
Information
This Interface Manual applies to all FIREBERD 4000
Communications Analyzers Incorporating Software Revision
6.0, or higher and to all FIREBERD 6000 Communications
Analyzers incorporating Sofware Revision J or higher.
1.0 GENERAL INFORMATION . 1 -1
1.1
INTRODUCTION., ... 1-1
1.2 Interface
FEATURES ... 1-1
1.3 Interface
COMPATIBILITY ... 1-2
1.4 OPTIONS AND
ACCESSORIES ... 1-2
2.0 Interface
DESCRIPTION ... 2-1
2.1 INTRODUCTION
... 2-1
2.2 PHYSICAL DESCRIPTION
... 2-1
2.2.1 Data Link/DSO RS-232
... 2-1
2.2.2 RX INPUT/TX
OUTPUT ... 2-2
2.2.3 T1 Ref
Input ... 2-2
2.2.4
Handset ... 2-2
2.3 FUNCTIONAL DESCRIPTION
... 2-3
2.3.1 Full T1
... 2-3
2.3.2 Fractional T1
... 2-4
2.3.3 T1/FT1 Drop and
Insert ... 2-4
2.3.4 ANSI T1.403 PRM
... 2-4
2.3.5 Voice
... 2-4
2.3.6 Test Loopback TLB
... 2-4
2.3.7 Line Loopback
LLB ... 2-4
2.3.8 ESF Data Link
... 2-4
2.3.9 RS232
... 2-5
2.4 SELF-LOOP OPERATION
... 2-5
3.0 FIREBERD 6000 INSTALLATION AND OPERATION
... 3-1
3.1
INTRODUCTION ... 3-1
3.2 INSTALLING THE Interface
... 3-1
3.3 FIREBERD 6000 MAINFRAME SET-UP
...
3-2
3.4 FIREBERD 6000 Interface MENU
... 3-2
3.4.1 FIREBERD 6000 Interface Menu
Control ... 3-2
3.4.2 Configuration
Menu ... 3-4
3.4.3 Mode Menu
... 3-5
3.4.4 Error insert
Menu ... 3-8
3.4.5 Idle Selection
Menu ... 3-8
3.4.6 Loop Type
Menu ... 3-8
3.4.7 Receive Byte Selection
Menu ... 3-9
3.5 FIREBERD 6000 ANALYSIS
RESULTS ... 3-10
3.6 Interface STATUS INDICATORS AND
SWITCHES ... 3-14
3.7 FIREBERD 6000 PRINTER
OPERATION ... 3-15
3.8 FIREBERD 6000 REMOTE CONTROL
COMMANDS ... 3-16
3.9 FIREBERD 6000 SELF-LOOP
TEST ... 3-19
4.0 FIREBERD 6000 APPLICATIONS 4-1
4.1
INTRODUCTION ... 4-1
4.2 END-TO-END FRACTIONAL T1
TESTING ... 4-1
4.3 CSU LOOPBACK
TESTING ... 4-2
4.4 INSTALLING AND TROUBLESHOOTING CUSTOMER PREMISE
EQUIPMENT ... 4-4
4.5 T1/FT1 DROP AND
INSERT ... 4-5
5.0 Fireberd 4000 INSTALLATION AND OPERATION
... 5-1
5.1
INTRODUCTION ... 5-1
5.2 INSTALLING THE Interface
... 5-1
5.3 Fireberd 4000 MAINFRAME SET-UP
... 5-2
5.4 Fireberd 4000 Interface
MENU ... 5-2
5.4.1 Fireberd 4000 Interface Menu
Control ... 5-2
5.4.2 Framing
Menu ... 5-2
5.4.3 Coding
Menu ... 5-4
5.4.4 Input
Menu ... 5-4
5.4.5 Line Build Out
Menu ... 5-4
5.4.6 Mode
Menu ... 5-5
5.4.7 Idle Selection
Menu ... 5-7
5.4.8 Error Insert
Menu ... 5-7
5.4.9 Loop Type
Menu ... 5-8
5.4.10 Loop Code Response Selection
Menu ... 5-9
5.4.11 Receive Byte Selection
Menu ... 5-9
5.4.12 Reference T1
Menu ... 5-9
5.5 Fireberd 4000 ANALYSIS
RESULTS ... 5-9
5.6 Interface STATUS INDICATORS AND
SWITCHES ... 5-11
5.7 Fireberd 4000 PRINTER
OPERATION ... 5-12
5.8 Fireberd 4000 REMOTE CONTROL
COMMANDS ... 5-13
5.9 Fireberd 4000 SELF-LOOP TEST
... 5-16
6.0 FIREBERD 4000
APPLICATIONS ... 6-1
6.1 INTRODUCTION
... 6-1
6.2 END-TO-END FRACTIONAL T1
TESTING ... 6-1
6.3 CSU LOOPBACK
TESTING ... 6-2
6.4 INSTALLING AND TROUBLESHOOTING CUSTOMER PREMISE
EQUIPMENT ... 6-4
6.5 T1 /FT 1 DROP AND
INSERT ... 6-5
7.0 SPECIFICATIONS
... 7-1
7.1
INTRODUCTION ...
7-1
8.0 MAINTENANCE AND
SERVICE ... 8-1
8.1 INTRODUCTION
...
8-1
8.2
MAINTENANCE ... 8-1
8.2.1 In Case of
Difficulty ... 8-1
8.3 SERVICE
... 8-1
8.3.1 Warranty
Policy ... 8-1
8.3.2 In-Warranty
Service ... 8-2
8.3.3 Out-Of-Warranty
Service ... 8-2
8.3.4 Equipment Return
Instructions ... 8-2