Geräte Informationen:

Rohde & Schwarz EB 100 641.8018.08 Analyzer
Hersteller:
Rohde & Schwarz
Modell: EB 100 641.8018.08
Datum: 1985
Kategorie: Messgeräte
Gruppe: Analyzer
Beschreibung: Miniport Receiver
Informationen:
                                    

Folgende Anleitungen sind hier verfügbar:

Dokumenttyp: Serviceanleitung RohdeUndSchwarz-8086-Manual-Page-1-Picture
Seitenanzahl: 188
Dateigröße: 5.81 Mbytes (6095445 Bytes)
Sprache: english,german
Revision:
Dokument-ID/Nummer: 754.2408.02
Datum: 01 Januar 1985
Qualität: Gescanntes Dokument, alles ist lesbar.
Upload Datum:
MD5: fe637a1aba86f97872463c1b7edbdbc7
Downloads: 144 seit dem 11 Dezember 2016
Informationen:
5_._Maintenance..................................5

5.1	Electrical Maintenance ......................5

5.2	Mechanical Maintenance ......................5

5-3 Storage......................................5

6._Performance Test............................6

6.1	Preliminary Remarks ..........................6

6.2	Required Measuring Equipment and

Accessories ..................................7

6.3	Checking the Puses PI and F2................8

6.3.1	Changing the Puses FI and F2................8

6.4	Battery Check ................................8

6.5	Illumination ................................8

6.6	Checking Operation by means of the Keypad . .	9

6.7	Tuning Knob..................................9

6.8	Function of Carrier Squelch ..................9

6.9	Checking the IF Filter......................9

6.10	Frequency Accuracy ..........................10

6.11	Checking the Signal Level Display and

the Level Tone ...........................11

6.12	Sensitivity .................	11

6.13	Measuring the Image Frequency Rejection ...	11

6.14	IP Rejection................................12

6.15	Oscillator Re-radiation at the Antenna ...	12

6.16	Checking the AFC Function....................13

6.17	AF Output....................................13

6.18	AF S/N Ratio at Vln = 1 mV . .'..............13

6.19	Checking the Power-Down Logic for the

CPU D301....................................13

6.20	Peak rectifier..............................14

t

6.21	IF Output........................14

_Troubleshooting of Subassembly..............15
8_._Removal of Subassemblies....................18

8.1	Synthesizer..................................19

8.2	Tuning Unit..................................19

8.3	Tuner........................................19

8.4	IP Section..................................20

8.5	Control Unit................................20

9	._Circuit Description..........................21

9.1	Tuner........................................21

9.2	IP Section..................................22

9.3	Synthesizer ...............................25

9.4	Control Unit................................25

9.5	Tuning Unit..................................28

10._Troubleshooting and Repair of

Subassemblies ..... ......................31

10.1	Preliminary Remarks ..........................31

10.1.1	Spare Parts.................. 31

10.1.2	Required Measuring Equipment and

Accessories..................................32

10.2	Troubleshooting..............................35

10.2.1	Tuner Fault Tracing Chart....................35

10.2.2	IF Section Fault Tracing Chart ..............39

10.2.3	Synthesizer Fault Tracing Chart ..............43

10.2.4	Control Unit Fault Tracing Chart ............46

10.2.5	Tuning Unit Fault Tracing Chart ..............52

10.3	Electrical Test and Adjustment of

Subassemblies ................................54

10.3.1	Tuner........................................54

10.3.1.1	Checking the Overall Gain....................54

10.3.1.2	Checking the 40-dB Attenuator . .............55

10.3.1.3	Checking the 1st VHF/UHF Amplifier and

1000-MHz Lowpass Filter ......................55

10.3.1.4	Checking 1st Mixer..........................55

10.3.1.5	Checking 2nd VHF/UHF Amplifier ..............56
10.3.1.6	Checking the Input Signal Path for

f ^ 500 MHz .................	56

10.3.1.7	Checking the UHP Amplifier ..................57

10.3.1.8	Checking the Input Signal Path for

f < 500 MHz •••••••••••••••••	57

10 .3 .1*9 Checking 2nd Mixer and Subsequent

Amplifier....................................58

10.3.1.10	Adjustment of the 650-MHz Lowpass Filter . .	58

10.3.1.11	Adjustment of the 629 .3-MHz Bandpass

Filter ...................	59

10.3.1.12	Adjustment of 117.3-MHz Bandpass Filter ...	59

10.3.2	IF Section..................................60

10.3.2.1	Overall Check of IF Section ..................60

10.3.2.2	Checking the 128-MHz Oscillator ..............6l

10.3.2.3	Checking th Signal Path......................6l

10.3.2.4	Checking the Output and Control Signals ...	62

10.3.2.5	Checking the Oscillator Reference Signals . .	63

10.3.3	Synthesizer ..................................64

10.3.3.1	Checking the Oscillator Signal ..............64

10.3.3.2	Checking the Oscillator and the

512-MHz Mixer ................................64

10.3.3.3	Checking the Divider Chain..................65

10.3.3.4	Checking the Reference Frequency

Generation...........................65

10.3.4	Control Unit.................65

10.3.4.1	Checking the System Clock ....................66

10.3.4.2	Checking the Reading and Writing Signals . .	66

10	*3 *5 Tuning Unit .................	66

10.3.5.1	Checking the Tuning Pulse Generation ....	66

10.3.5.2	Checking the AF Amplifier....................66

10.3.5.3	Checking the Level Tone Generator ............67
Pig. 11-1 Test set-up for functional test

Pig. 11-2 Test set-up for checking the 3-db bandwidth 150
kHz Pig. 11-3 Test set-up for checking the peak rectifier
Pig. 11-4 Removal of assemblies (without control unit)

Pig. 11-5 Removal of control unit

Service documentation
RohdeUndSchwarz-8086-Manual-Page-1-Picture


Comments (0)

No comments yet. Be the first!

Add Comment

* Required information
1000
Captcha Image
Powered by Commentics