Geräte Informationen:

Electronic Navigation Industries 350L Verstärker
Hersteller:
Electronic Navigation Industries
Modell: 350L
Datum:
Kategorie: Funk und Kommunikation
Gruppe: Verstärker
Beschreibung: BROADBAND POWER AMPLIFIER
Informationen:
                                    The ENi Model 350L is an all solid state amplifier which has
a flat frequency response from 250 kHz to 105 MHz.
It provides 50 watts of linear power with low harmonic and
intermodulation distortion. Gain is 50 dB nominal, with a
variation of less than +1.5 dB over the entire frequency
range. Input and output impedance are 50 ohms and the unit
may be driven to full power output by most RF synthesizers,
signal generators and swept signal sources.
The ENI Model 350L will deliver its rated power output into
any load impedance, regardless of match, Buiit-in protection
circuitry will absorb the power reflected from a mismatched
load without causing failure or oscillation.
Output RF voltage is displayed on the front panel meter. The
Model 350L is packaged for bench mounting and is shipped
with rack mounting adapters. Its integral power
supply and cooling operate from a 115 or 230 VAC 50/60Hz
main supply.
The Model 350L will raise the power level of signal sources
and generators without requiring tuning or band- switching.
The Class A linear circuitry will amplify signals of AM, FM,
SSß, TV and complex modulations limited only by their peak
input and bandwidth with minimum distortion.

Folgende Anleitungen sind für obiges Gerät verfügbar:

Electronic Navigation Industries -- 350L -- Bedienungsanleitung
Dateiname: ENI-7553-Manual-Page-1-Picture
Dokumenttyp: Bedienungsanleitung
Seitenanzahl: 16
Dateigröße: 525.22 Kbytes (537824 Bytes)
Sprache: Englisch
Revision:
Dokument-ID/Nummer:
Datum:
Qualität: Gescanntes Dokument, teilweise schwer oder teilweise nicht zu lesen.
Upload Datum:
MD5: 42d3c760fea09431ddcc91c6820d0f01
ed2kID: a696f3fb19669e23fc3c6def137f7fd4
Downloads: 25 seit 25 Januar 2016
Informationen:
CHAPTER 1
INTRODUCTION
1.1
General Description......................
1-1
1.2
Specifications................................
M
1.3
Instrument Identification . . . .
1-1
CHAPTER 2
PREPARATION
2.1
Initial Inspection ........................
2-1
2.1.1
Mechanical Check........................
2-1
2.1.2
Claim for Damage ......................
2-1
2.1.3
Performance Check......................
2-1
2.2
Preparation for Use......................
2-1
2.2.1
Power Requirements......................
2-1
2.2.2
Power Cable Ground Protection ,
2-1
2.2.3
Cooling...........................................
2-1
2.3
Rack Mounting ...........................
2-1
2.4
Packaging for Reshipment . . . .
2-1
CHAPTER 3 OPERATION
3.1
Functional Description ..............
3-1
3.2
Controls, Indicators and
Connectors .............................
3-1
3.3
Operating Procedure ...................
3-1
3.4
Precautions.....................................
3-2
CHAPTER 4 PRINCIPLES OF OPERATION
4.1
General...........................................
4-1
4.2
Block Diagram Description . , ,
4-1
4.2.1
Preamplifier Module (A22)
3501.-4185 ■..............................
4-1
4.2.2
Driver Amplifier Module (A1)
350L-4181................................
4-1
4.2.3
Power Amplifier Module (A21)
350L-4184................................
4-1
4.2.4
Combiner Module (A23)
350L-4186................................
4-3
4.2.5
RF Voltmeter Module (A 12)
350L-4182................................
4-3
4.2.6
Power Distribution
350L-2181 ..............................
4-3
CHAPTER 5
PERFORMANCE
TEST PROCEDURES
5.1
Performance Tests......................
5-1
5.1.1
General , ,................................
. . 5-1
5.1.2
Test Equipment Required . , ,
. . 5-1
5.1.3
Gain and Gain Variation Test .
. · 5-1
5,1.3.1
Calibration of Set Up ..............
. . 5-1
Paragraph
Page
5.1.3.2
Measurement Procedure ................
5-1
5.1.4
RF Output Power Test...................
5-2
5.1.4.1
Measurement Procedure ................
5-2
5.1.5
RF Output Distortion Test...........
5-2
5.1.5.1
Measurement Procedure ................
5-2
CHAPTER 6 TROUBLESHOOTING AND REPAIR
6.1
Troubleshooting.............................
6-1

The end of the manual with schematics is missing!
ENI-7553-Manual-Page-1-Picture
Kostenlos herunterladen


Kommentare

Noch keine Kommentare vorhanden.

Kommentar Hinzufügen

* Pflichtfeld
(wird nicht veröffentlicht)
 
Bold Italic Underline Strike Superscript Subscript Quote Line Bullet Link Email Image Video
 
Smile Sad Huh Laugh Mad Tongue Crying Grin Wink Scared Cool Sleep Blush Unsure Shocked
 
1000
Enter the word shark backwards.
 
Die Antwort lautet:
 
Informiere mich via E-Mail über neue Kommentare.
 
Meine Daten auf diesem Computer.
 
 
Powered by Commentics