Geräte Informationen:

California Instruments 6000L-P Netzteil
Hersteller:
California Instruments
Modell: 6000L-P
Datum: 2001
Kategorie: Messgeräte
Gruppe: Netzteil
Beschreibung: Power Source
Informationen:
                                    This power system is a high efficiency power source that
provides a low distortion output. The output can be
configured in either a single or three-phase configuration.
A number of Power Sources can be configured to supply full
output power up to 27000VA. Table 1-1 shows the output VA
per phase for each of the available power system models. The
table also shows that increased power is available at a
reduced operating temperature of 35?C.

Folgende Anleitungen sind hier verfügbar:

California Instruments -- 6000L-P -- Service- und Bedienungsanleitung
Dateiname: CaliforniaInstruments-7412-Manual-Page-1-Picture
Dokumenttyp: Service- und Bedienungsanleitung
Seitenanzahl: 151
Dateigröße: 1.28 Mbytes (1345007 Bytes)
Sprache: Englisch
Revision: K
Dokument-ID/Nummer: 4009-316
Datum: August 2001
Qualität: Gescanntes Dokument, alles ist lesbar.
Upload Datum:
MD5: d4f10b1e9514dd42297132951bea20a5
Downloads: 203 seit dem 20 Dezember 2015
Informationen:
SECTION 1 INTRODUCTION AND
SPECIFICATIONS--------------------------------------------------------------------------1
1.1
INTRODUCTION............................................................................................................................................1
1.2 GENERAL DESCRIPTION
-------------------------------------------------------------------------------------------------------
1
1.3 ACCESSORY EQUIPMENT/RACK
SLIDES-------------------------------------------------------------------------------
3
1.4
SPECIFICATIONS-----------------------------------------------------------------------------------------------------------------
3
SECTION 2 INSTALLATION AND
ACCEPTANCE-----------------------------------------------------------------------------13
2.1
UNPACKING-----------------------------------------------------------------------------------------------------------------------13
2.2 POWER
REQUIREMENTS.........................................................................................................................13
2.3 MECHANICAL
INSTALLATION..................................................................................................................13
2.4 INPUT
WIRING............................................................................................................................................13
2.5 OUTPUT
CONNECTIONS..........................................................................................................................20
2.6 OUTPUT VOLTAGE
RANGES....................................................................................................................20
2.7 FUNCTION
TEST.........................................................................................................................................20
2.8 REAR PANEL DIP SWITCH
(SW1)............................................................................................................21
SECTION 3
OPERATION----------------------------------------------------------------------------------------------------------------24
3.1
GENERAL--------------------------------------------------------------------------------------------------------------------------24
3.2 FRONT PANEL
CONTROLS-------------------------------------------------------------------------------------------------24
3.3 FRONT PANEL
INDICATORS------------------------------------------------------------------------------------------------24
3.4 REAR PANEL
CONNECTIONS----------------------------------------------------------------------------------------------26
3.5 FRONT PANEL
PROGRAMMING-------------------------------------------------------------------------------------------31
3.6 TO MEASURE THE
OUTPUT------------------------------------------------------------------------------------------------46
3.7 REMOTE PROGRAMMING WITH ABBREVIATED PLAIN ENGLISH
(APE)---------------------------------47
3.8 REMOTE OPERATION WITH MATE
CIIL--------------------------------------------------------------------------------67
SECTION 4 CALIBRATION
PROCEDURE-----------------------------------------------------------------------------------------82
4.1
GENERAL....................................................................................................................................................82
4.2 TEST
EQUIPMENT---------------------------------------------------------------------------------------------------------------83
4.3 PERIODIC
CALIBRATION------------------------------------------------------------------------------------------------------88
4.4 NONPERIODIC
CALIBRATION----------------------------------------------------------------------------------------------96
SECTION 5 THEORY OF
OPERATION--------------------------------------------------------------------------------------------105
5.1
GENERAL...................................................................................................................................................105
5.2 OVERALL
DESCRIPTION.........................................................................................................................105
5.3 INPUT POWER
SUPPLY..........................................................................................................................105
5.4 AUXILIARY POWER
SUPPLY..................................................................................................................107
5.5 CURRENT LIMIT
BOARD..........................................................................................................................107
5.6 INDICATOR
BOARD..................................................................................................................................107
5.7 RANGE RELAY
BOARD............................................................................................................................107
5.8 AMPLIFIER
MODULES.............................................................................................................................107
5.9 OSCILLATOR
MODULE............................................................................................................................108
5.10 CPU/GPIB
BOARD.....................................................................................................................................108
5.11 PHASE A/REF
BOARD..............................................................................................................................109
5.12 PHASE B/C
BOARD..................................................................................................................................109
5.13 DISPLAY
MODULE.....................................................................................................................................109
SECTION 6 MAINTENANCE AND
TROUBLESHOOTING-------------------------------------------------------------------111
6.1
GENERAL...................................................................................................................................................111
6.2 POOR VOLTAGE
ACCURACY----------------------------------------------------------------------------------------------111
6.3 POOR OUTPUT VOLTAGE
REGULATION..............................................................................................111
6.4 OVERTEMPERATURE LAMP
ON.............................................................................................................111
6.5 OVERLOAD LAMP
ON..............................................................................................................................112
6.6 CAN'T PROGRAM AC POWER SYSTEM ON
GPIB..............................................................................112
6.7 DISTORTED
OUTPUT..............................................................................................................................112
6.8 NO
OUTPUT-----------------------------------------------------------------------------------------------------------------------113
6.9 MODULE
REMOVAL------------------------------------------------------------------------------------------------------------113
6.10 OSCILLATOR MODULE
REMOVAL/REPLACEMENT...........................................................................113
6.11 AMPLIFIER
REMOVAL/REPLACEMENT................................................................................................114
SECTION 7 REPLACEABLE
PARTS-----------------------------------------------------------------------------------------------117
7.1
GENERAL...................................................................................................................................................117
7.2 ORDERING
INFORMATION.....................................................................................................................117
SECTION 8
MIL-STD-704D-------------------------------------------------------------------------------------------------------------119
8.1
GENERAL-------------------------------------------------------------------------------------------------------------------------119
8.2 INITIAL
SETUP--------------------------------------------------------------------------------------------------------------------119
8.3 TEST
PERFORMED------------------------------------------------------------------------------------------------------------119
8.4 KEYPAD ENTRY (Refer to page 31 for Keyboard flow
chart)...............................................................120
8.5 GPIB OPERATION (Refer to page 150 for syntax
diagram).................................................................122
8.6 TEST
SPECIFICATION.............................................................................................................................122
SECTION 9 2-PHASE OPTION
(2P)-------------------------------------------------------------------------------------------------135
9.1
GENERAL...................................................................................................................................................135
SECTION 10
RTCA/DO-160C---------------------------------------------------------------------------------------------------------137
10.1
GENERAL...................................................................................................................................................137
10.2 INITIAL
SETUP...........................................................................................................................................137
10.3 TEST
PERFORMED..................................................................................................................................137
10.4 KEYPAD ENTRY (Refer to Figure 1 for Keyboard Flow
Chart).............................................................137
10.5 GPIB
OPERATION.....................................................................................................................................139
10.6 TEST
SPECIFICATION.............................................................................................................................140
LIMITED
WARRANTY------------------------------------------------------------------------------------------------------------------------147
CaliforniaInstruments-7412-Manual-Page-1-Picture
Kostenlos herunterladen


Comments (0)

No comments yet. Be the first!

Add Comment

* Required information
1000
Which is darker: black or white?
Powered by Commentics