Geräte Informationen:

California Instruments 4503L Netzteil
Hersteller:
California Instruments
Modell: 4503L
Datum: 1990
Kategorie: Messgeräte
Gruppe: Netzteil
Beschreibung: Power Source
Informationen:
                                    This instrument is a high efficiency power source that
provides a low distortion sine wave output with either a
single or three-phase configuration. The AC Power System can
supply up to 4500VA in the single-phase mode or 15G0VA per
phase in the three-phase mode. Full power is available from
either a 0 to 135 volt range or 0 to 270 volt range. Full
power is available from 45 Hz to 550 Hz. The AC Power System
is illustrated in Figure 1- 1.

Folgende Anleitungen sind für obiges Gerät verfügbar:

California Instruments -- 4503L -- Service- und Bedienungsanleitung
Dateiname: CaliforniaInstruments-7400-Manual-Page-1-Picture
Dokumenttyp: Service- und Bedienungsanleitung
Seitenanzahl: 112
Dateigröße: 3.28 Mbytes (3443370 Bytes)
Sprache: Englisch
Revision:
Dokument-ID/Nummer: 4009-961
Datum: Dezember 1990
Qualität: Gescanntes Dokument, teilweise schwer oder teilweise nicht zu lesen.
Upload Datum:
MD5: 7abb094ab4c28348ce13754f8fae2dee
ed2kID: 0019756951d9ae98f6267c3ecb23261f
Downloads: 26 seit 20 Dezember 2015
Informationen:
1
2
SECTION
INTRODUCTION AND SPECIFICATIONS.............. 1
1-1 INTRODUCTION........................... 1
1-2 GENERAL DESCRIPTION..................... 1
1-4 ACCESSORY EQUIPMENT/RACK SLIDES........ 1
1-6 SPECIFICATIONS ......................... 1
INSTALLATION AND ACCEPTANCE................... 7
2-1 UNPACKING............................... 7
2-3 POWER REQUIREMENTS . ................. 7
2-5 MECHANICAL INSTALLATION. ........ 7
2-7 INPUT WIRING..................... 7
2-9 OUTPUT CONNECTIONS ..................... 7
2-14 OUTPUT VOLTAGE RANGES................... 9
2-16 FUNCTION TEST.......................... 9
TITLE PAGE
OPERATION..................................... 12
3-1 GENERAL................................ 12
3-3 FRONT PANEL CONTROLS................... 12
3-7 FRONT PANEL INDICATORS ........ .... 12
3-15 REAR PANEL CONNECTIONS................. 14
3-21 FRONT PANEL PROGRAMMING............... 18
3-22 KEYPAD . . . . ................. 18
3-25 DISPLAY SCREENS. ................. 20
3-32 TO PROGRAM OUTPUT VOLTAGE
AMPLITUDE <AMP=5).......... 25
3-34 TO PROGRAM FREQUENCY (FRQ=6) .... 25 3-36 TO PROGRAM
OUTPUT PHASF
ANGLE (PHZ-7) ............. 26
3-39 TO PROGRAM CURRENT LIMIT (CLR=8) . . 26
3-41 TO PROGRAM VOLTAGE RANGE (RNG=4) . . 27 3-44 TO PROGRAM
RAMP OR STEP
FUNCTION (RMP*9)....... 27
3-56 TO PROGRAM THE OUTPUT
WAVEFORM. .......... 30
3-61 TO PROGRAM EXTERNAL
SYNCHRONIZATION ............ 3 0
3-67 TO PROGRAM THE EXTERNAL
CLOCK (CLK-2)............... 31
3-70 TO PROGRAM REGISTERS
AND RAMPS............ 31
3-74 REGISTER LINKING................... 3 2
3-77 TO PROGRAM SIMULTANEOUS RAMPS. ... 33
3-BO ERROR MESSAGES.................... 3 4
3-82 TO MEASURE THE OUTPUT.......... 36
3-85 TO MEASURE THE OUTPUT
VOLTAGE (VLT=21)............ 36
3-87 TO MEASURE THE OUTPUT
CURRENT (CUR=22). ...... 36
3-89 TO MEASURE THE OUTPUT
POWER (PWR=23).......... 36
3-91 TO MEASURE THE OUTPUT
POWER FACTOR (PWF=24) .... 36 3-93 TO MEASURE THE OUTPUT
APPARENT POWER (APW=25) ... 36 3-9 5 TO MEASURE THE OUTPUT
FREQUENCY (FQM=26).......... 37
3-97 TO MEASURE THE OUTPUT
PHASE ANGLE (PZM=27)........ 37
3-99 ELAPSED TIME (ELT=11)............ 37
3-101 REMOTE CONTROL ................. 0 „ , . 37
3-103 UNIT ADDRESS...........................37
3-106 MESSAGE FORMAT.................. . 41
3-108 NUMERIC DATA FIELD.............. . 41
3-112 PROGRAM HEADERS.........................42
3-118 TO PROGRAM FREQUENCY (FRQ) ..... 48
3-121 TO PROGRAM PHASE ANGLE (PHZ) .... 48
3-125 TO PROGRAM CURRENT LIMIT..............49
3-128 TO PROGRAM CALIBRATION................49
3-136 TO PROGRAM RAMP OR STEP
OPERATIONS. .....................50
3-150 TO PROGRAM A REGISTER (REG)..... 51
3-153 TO RECALL A REGISTER (REC)............51
3-158 TO PROGRAM VOLTAGE RANGE (RNG) ... 52
3-161 TO PROGRAM EXTERNAL
SYNCHRONIZATION (SNC) . . . . 5 2 3-165 TO PROGRAM EXTERNAL
CLOCK
(CLK) (Optional)................52
3-168 TO TRIGGER AN OPERATION (TRG). ... 53
3-171 TO PROGRAM TO OUTPUT
WAVEFORM CWVF) (Optional) . . 53 3-175 TO OPEN (OPN) AND
CLOSE (CLS)
THE OUTPUT RELAY................5 4
3-177 TO TALK (TLK) MEASURED AND
PROGRAMMED DATA................5 4
3-182 TO TALK THE MEASURED OUTPUT
VOLTAGE (TLK VLT)..............5 8
3-185 TO TALK THE MEASURED OUTPUT
CURRENT (TLK CUR)..............5 8
3-188 TO TALK THE MEASURED OUTPUT
POWER (TLK PWR)................5 8
3-191 TO TALK THE MEASURE OUTPUT
POWER FACTOR (TLK PWF).... 58 3-194 TO TALK THE MEASURED OUTPUT
APPARENT POWER (TLK APW). . . 58 3-197 TO TALK THE MEASURED
OUTPUT
FREQUENCY (TLK FRQ)............5 9
3-200 TO. TALK THE MEASURED OUTPUT
PHASE ANGLE (TLK PZM) .... 59
3-203 MESSAGE SEPARATORS................ 59
3-206 SERVICE REQUEST.........................59
3-209 SERIAL POLL STATUS BYTE. ...... 60
3-211 END OF STRING....................... 60
3-213 ERROR MESSAGES................ 60
3-215 GROUP EXECUTE TRIGGER.............. 60
3-219 HEWLETT PACKARD SERIES 80
PROGRAM EXAMPLES............ 6 3
4 CALIBRATION PROCEDURE
4-1 GENERAL. . . .......................... 6 5
4-4 TEST EQUIPMENT...................... . 66
4-6 PERIODIC CALIBRATION ................... 68
4-8 OUTPUT VOLTAGE CALIBRATION ........ 68
4-12 MEASUREMENT CALIBRATION............ 68
4-16 REMOTE MEASUREMENT CALIBRATION ........ 7 2
4-21 REMOTE OUTPUT VOLTAGE CALIBRATION. ... 72
4-25 NONPERIODIC CALIBRATION................ 73
4-27 OUTPUT FREQUENCY CALIBRATION . . . . 73 4-30 GAIN
ADJUSTMENTS FOR 1-BOX
3-PHASE SYSTEM.............. 73
4-36 GAIN ADJUSTMENTS FOR 1-BOX
1-PHASE SYSTEM.............. 78
4-39 CURRENT TRANSFORMER ADJUSTMENTS
FOR 1-BOX 3-PHASE SYSTEM. . . 78 4-41 CURRENT TRANSFORMER
ADJUSTMENTS
FOR 1-BOX 1-PHASE SYSTEM. . . 79 4-43 SINGLE-PHASE
ADJUSTMENTS FOR
FOR 1 BOX SYSTEM............ 79
4-45 CURRENT LIMIT CALIBRATION.......... 80
4-47 OUTPUT PHASE ANGLE CALIBRATION ... 80
5 THEORY OF OPERATION........................... 82
5-1 GENERAL................................ 82
5-2 OVERALL DESCRIPTION..................... 82
5-8 INPUT POWER SUPPLY ..................... 82
5-12 AUXILIARY POWER SUPPLY . ............... 84
5-14 CURRENT LIMIT BOARD..................... 84
5-18 INDICATOR BOARD........................ 84
5-21 RANGE RELAY BOARD....................... 85
5-25 AMPLIFIER MODULES....................... 85
5-31 OSCILLATOR MODULES ..................... 85
5-33 CPU/GPIB BOARD......................... 87
5-40 PHASE A/REF BOARD....................... 87
5-42 PHASE B/C BOARD................. 87
5-44 DISPLAY MODULE . . ..................... 88
6 MAINTENANCE AND TROUBLESHOOTING.............. 89
6-1 GENERAL........'....................... 89
6-3 POOR VOLTAGE ACCURACY................... 89
6-5 POOR OUTPUT VOLTAGE REGULATION ........ 89
6-7 OVERTEMPERATURE LAMP ON................ 90
6-9 OVERLOAD LAMP ON....................... 90
6-11 CAN’T PROGRAM AC POWER SYSTEM ON GPIB. . 91
6-13 DISTORTED OUTPUT ....................... 91
6-15 NO OUTPUT............................... 91
TITLE PAGE
6-17 MODULE REMOVAL......................... 92
6-19 OSCILLATOR MODULE REMOVAL/REPLACEMENT. . 92
6-21 AMPLIFIER REMOVAL/REPLACEMENT.......... 93
7 REPLACEABLE PARTS
7-1 GENERAL................................. 95
7-3 ORDERING INFORMATION ................... 95
CaliforniaInstruments-7400-Manual-Page-1-Picture
Kostenlos herunterladen


Kommentare

Noch keine Kommentare vorhanden.

Kommentar Hinzufügen

* Pflichtfeld
(wird nicht veröffentlicht)
 
Bold Italic Underline Strike Superscript Subscript Quote Line Bullet Link Email Image Video
 
Smile Sad Huh Laugh Mad Tongue Crying Grin Wink Scared Cool Sleep Blush Unsure Shocked
 
1000
What is the day after Friday?
 
Die Antwort lautet:
 
Informiere mich via E-Mail über neue Kommentare.
 
Meine Daten auf diesem Computer.
 
 
Powered by Commentics