Geräte Informationen:

Kikusui Electronics Corporation PMC35-1A Sonstiges
Hersteller:
Kikusui Electronics Corporation
Modell: PMC35-1A
Datum: 1994
Kategorie: Messgeräte
Gruppe: Sonstiges
Beschreibung: REGULATED DC POWER SUPPLY
Informationen:
                                    The PMC-A series Regulated DC Power Supply is an automatic
constant voltage/constant current shift type. It employs a
series regulator system and delivers a stable output wish
low noise.
• The PMC-A series, which has two bright 3-l/2digit LED
display meters, displays the output voltage and the output
current or their settings.
» The potentiometers for the output voltage and current
setting are 10 turns wire wound type, allowing
high-resolution setting and stable output.
• The output switch is an electronic switch. It causes no
chattering or noise. It can be controlled from the panel or
from a remote place.
• The output voltage and current can be remote-controlled by
an external analog signal (voltage or Resistor). The PMC-A
series can be used as a system component of an automation
system with GPIB interface such as KIKUSUI’s PIA 3200.
ThePMC-A series can be used in a wide application field from
use in a laboratory for experiment to that on a production
line for testing.

Folgende Anleitungen sind hier verfügbar:

Kikusui Electronics Corporation -- PMC35-1A -- Bedienungsanleitung
Dateiname: Kikusi-7065-Manual-Page-1-Picture
Dokumenttyp: Bedienungsanleitung
Seitenanzahl: 34
Dateigröße: 861.98 Kbytes (882669 Bytes)
Sprache: Englisch
Revision:
Dokument-ID/Nummer: Z1 -000-582 IA000791
Datum: 1994
Qualität: Gescanntes Dokument, teilweise schwer oder teilweise nicht zu lesen.
Upload Datum:
MD5: 5314dd6f1a65979aa2b0b17a320f4798
Downloads: 231 seit dem 14 August 2015
Informationen:
SAFETY
SUMMARY............................................................................................
I CHECK AT
UNPACKING.....................................................................................
ffl PACKING FOR
RE-SHIPMENT..........................................................................
IE Chapter 1 GENERAL
DESCRIPTION.............................................................
1 Chapter 2 PRECAUTION AND PREPARATION FOR
USE......................... 1
2.1 Inrush
Current...........................................................................
1
2.2
Environment.............................................................................
2
2.3 Type οΓ Load
............................*...............................................
3
Chapter 3 PANEL
DESCRIPTION..................................................................
4
3.1 Front
Panel............*.........................................-.......................
4
3.2 Rear
Panel...........*...................................................................
6
Chapter 4 OPERATING
METHOD..................................................................
7
4.1 Basic
Operation..............................*—·**..................................
7
4.1.1 Turning the POWER switch
on/off....................................... 7
4.1.2 Setting the output voltage or current,
and turning the output on/off
................................................ 7
4.1.3 OVP trip voltage
setting..............................*...........*............ 7
4.2 Applied
Operation....................................................'·-**.............
8
4.2.1 Remote
sensing**···——........—*.............................................8
4.2.2 Analog remote
control............................................................8
4.2.3 Series operation and parallel
operation...................................12
4.2.4 Master/Slave controlled parallel
operation...................*.........14
Chapter 5 MAINTENANCE AND
CALIBRATION..............................*........... 15
5.1 Maintenance and Checking
.............................................*.......... 15
5.2
Calibration................................-.............................*.................
15
5.2.1
Preparation..................*..........................................................15
5.2.2 Test equipment
required................*.......................................16
5.2.3 Calibration setup
·■—.......*.......................................................16
5.2.4 Calibration procedure
.............................................................17
Chapter 6
SPECIFICATIONS.......................................................................····
19
6.1 Electrical Specifications
···■·....................................................... 19
6.2
Dimensions......................................................................................................
21
6.3
Option.......................................................................................
21
Kikusi-7065-Manual-Page-1-Picture
Kostenlos herunterladen


Comments (0)

No comments yet. Be the first!

Add Comment

* Required information
1000
What is the day after Friday?
Powered by Commentics