Geräte Informationen:

Kikusui Electronics Corporation PMC18-2A Sonstiges
Hersteller:
Kikusui Electronics Corporation
Modell: PMC18-2A
Datum: 1994
Kategorie: Messgeräte
Gruppe: Sonstiges
Beschreibung: REGULATED DC POWER SUPPLY
Informationen:
                                    The PMC-A series Regulated DC Power Supply is an automatic
constant voltage/constant current shift type. It employs a
series regulator system and delivers a stable output wish
low noise.
• The PMC-A series, which has two bright 3-l/2digit LED
display meters, displays the output voltage and the output
current or their settings.
» The potentiometers for the output voltage and current
setting are 10 turns wire wound type, allowing
high-resolution setting and stable output.
• The output switch is an electronic switch. It causes no
chattering or noise. It can be controlled from the panel or
from a remote place.
• The output voltage and current can be remote-controlled by
an external analog signal (voltage or Resistor). The PMC-A
series can be used as a system component of an automation
system with GPIB interface such as KIKUSUI’s PIA 3200.
ThePMC-A series can be used in a wide application field from
use in a laboratory for experiment to that on a production
line for testing.

Folgende Anleitungen sind für obiges Gerät verfügbar:

Kikusui Electronics Corporation -- PMC18-2A -- Bedienungsanleitung
Dateiname: Kikusi-7065-Manual-Page-1-Picture
Dokumenttyp: Bedienungsanleitung
Seitenanzahl: 34
Dateigröße: 861.98 Kbytes (882669 Bytes)
Sprache: Englisch
Revision:
Dokument-ID/Nummer: Z1 -000-582 IA000791
Datum: 1994
Qualität: Gescanntes Dokument, teilweise schwer oder teilweise nicht zu lesen.
Upload Datum:
MD5: 5314dd6f1a65979aa2b0b17a320f4798
ed2kID: 0d23dc86a5cb686bcfd9f58da4991830
Downloads: 93 seit 14 August 2015
Informationen:
SAFETY
SUMMARY............................................................................................
I CHECK AT
UNPACKING.....................................................................................
ffl PACKING FOR
RE-SHIPMENT..........................................................................
IE Chapter 1 GENERAL
DESCRIPTION.............................................................
1 Chapter 2 PRECAUTION AND PREPARATION FOR
USE......................... 1
2.1 Inrush
Current...........................................................................
1
2.2
Environment.............................................................................
2
2.3 Type οΓ Load
............................*...............................................
3
Chapter 3 PANEL
DESCRIPTION..................................................................
4
3.1 Front
Panel............*.........................................-.......................
4
3.2 Rear
Panel...........*...................................................................
6
Chapter 4 OPERATING
METHOD..................................................................
7
4.1 Basic
Operation..............................*—·**..................................
7
4.1.1 Turning the POWER switch
on/off....................................... 7
4.1.2 Setting the output voltage or current,
and turning the output on/off
................................................ 7
4.1.3 OVP trip voltage
setting..............................*...........*............ 7
4.2 Applied
Operation....................................................'·-**.............
8
4.2.1 Remote
sensing**···——........—*.............................................8
4.2.2 Analog remote
control............................................................8
4.2.3 Series operation and parallel
operation...................................12
4.2.4 Master/Slave controlled parallel
operation...................*.........14
Chapter 5 MAINTENANCE AND
CALIBRATION..............................*........... 15
5.1 Maintenance and Checking
.............................................*.......... 15
5.2
Calibration................................-.............................*.................
15
5.2.1
Preparation..................*..........................................................15
5.2.2 Test equipment
required................*.......................................16
5.2.3 Calibration setup
·■—.......*.......................................................16
5.2.4 Calibration procedure
.............................................................17
Chapter 6
SPECIFICATIONS.......................................................................····
19
6.1 Electrical Specifications
···■·....................................................... 19
6.2
Dimensions......................................................................................................
21
6.3
Option.......................................................................................
21
Kikusi-7065-Manual-Page-1-Picture
Kostenlos herunterladen


Kommentare

Noch keine Kommentare vorhanden.

Kommentar Hinzufügen

* Pflichtfeld
(wird nicht veröffentlicht)
 
Bold Italic Underline Strike Superscript Subscript Quote Line Bullet Link Email Image Video
 
Smile Sad Huh Laugh Mad Tongue Crying Grin Wink Scared Cool Sleep Blush Unsure Shocked
 
1000
Enter the word table backwards.
 
Die Antwort lautet:
 
Informiere mich via E-Mail über neue Kommentare.
 
Meine Daten auf diesem Computer.
 
 
Powered by Commentics