Geräte Informationen:

Iwatsu SS-5711 Oszilloskop
Hersteller:
Iwatsu
Modell: SS-5711
Datum:
Kategorie: Messgeräte
Gruppe: Oszilloskop
Beschreibung:
Informationen:
                                    The 55-5711 is an oscilloscope with a frequency bandwidth
of DC to 100 MHz that can display 8 traces on 4
channels.
The SS~5711 is useful in a wide range of applications for
not only production lines and maintenance and service
purposes but also for the research and development of a
variety of electronic devices. The features of the SS-5711
are as follows:
'In addition to display of 8 traces on 4 channels. the SS-5711
has an ADD function for measuring the sum of two signals
and CH 2 POLAR for measurement of the difference between
two signals.
• Both CH 1 and CH 2 have a high deflection factor of 1
mV Idiv (in the x5 MAG function). which permits accurate
measurement of voltages.
· The horizontal deflection system has sweep rates up to
2 nsec/div (in the xl0 MAG function Iso that even highspeed
phenomena can be measured with accuracy.
• The SS-5711 has delayed sweep. single sweep. AL T
sweep, and X-V operation functions, and a TV synchronizing
signal separator circuit so that television and other
composite video signal waveforms can be observed.

Folgende Anleitungen sind für obiges Gerät verfügbar:

Iwatsu -- SS-5711 -- Serviceanleitung
Dateiname: Iwatsu-6698-Manual-Page-1-Picture
Dokumenttyp: Serviceanleitung
Seitenanzahl: 196
Dateigröße: 11.44 Mbytes (11991243 Bytes)
Sprache: Englisch
Revision:
Dokument-ID/Nummer:
Datum:
Qualität: Gescanntes Dokument, alles ist lesbar.
Upload Datum:
MD5: dbfa5b52cce47dd23fb71d2defc1b1a3
ed2kID: da7e3a6d45387dd4ae1a1d426404b2d6
Downloads: 93 seit 14 Mai 2015
Informationen:
SECTION 1 SPECIFiCATIONS __ ..•.•.....•. 1-1
1-1 GENERAL .................. 1-1
1-2 ELECTRICAL SPECIFICATIONS .. 1-1
1-2-1 Cathode-Ray Tube (CRT) ...... 1-1
1-2-2 Vertical Deflection System ..... 1-1
1-2-3 Triggering ................ 1-2
1-2-4 Horizontal Deflection System ... 1-3
1-2-5 x-v Operation ............. 1-4
1-2-6 Z-Axis System ............. 1-4
1-2-7 Signal Output. ............. 1-4
1-2-8 Power Supply .............. 1-5
1-3 PHASICAL CHARACTERISTICS .. 1-5
1-4 ENVI RONMENTAL
CHARACTERISTICS ......... 1-5
ACCESSORIS ................ 1-5
OPERATING INFORMATION ...••• 2-1
OPERATING PRECAUTIONS ..... 2-1
OPERATION OF THE HANDLE ... 2-2
CONTROLS AND SWITCHES ..... 2-2
Front Panel ............... 2-3
Rear Panel. . . . . . . . . . . . . . . . 2-8
Bottom Cover. . . . . . . . . . . . . . 2-8
OPERATIONG INSTRUCTIONS ... 2-10
Basic Operation for Signal
Observation ............. 2-10
Applying Signals ............ 2-11
Signal Input Coupling Section ... 2-11
Vertical Defection Factor Setting .2-12
Triggering ................ 2-12
Sweep Rate Setting •.......... 2-15
APPLIED OPERATIONS FOR SIGNAL
OBSERVATION ............ 2-15
Operation for Dual-Trace
Observation ............. 2-15
Operation for Observation of the Sum
of Two Signals or Their
Difference ........... 2-16
Operation for Quadruple-Trace
Observation ............. 2-16
2·5·4 Operation for Enlarging Waveforms
on the CRT Screen .......... 2-17
2-5-5 Operation for AL T Sweep ...... 2-18
2-5-6 Operation for Observing Television
Composite Video Signal
Waveforms ........... 2-1 9
2-5-7 Operation for Single Sweep ..... 2-20
2-5-8 Operation for Use as an x-Y
Scope ................. 2-21
2-5-9 Z Axis System ............. 2-21
SECTION 3 MEASURING PROCEDURES ••••••• 3-1
3-1 ADJUSTMENTS NECESSARY BEFORE
MEASUREMENTS .......... 3-1
TRACE ROTATION Adjustment. 3-1
GAIN Adjustment. .......... 3-1
x5 SAL Adjustment .......... 3-1
VARIABLE SAL Adjustment ... 3-1
Probe Phase Adjustment. ...... 3-1
MEASURING METHODS ........ 3-2
Voltage Measurement. ........ 3-2
Current Measurement ...... , .. 3-3
Time Measurement .......... 3-4
Frequency Measurement ..... " . 3-5
Phase Difference Measurement ... 3-5
THEORY OF OPERATION ..•.••.• 4-1
GENERAL. ................. 4-1
Pre-amplifiers for Channels
1, 2, 3, and 4 ............. 4-1
Delay Cable Driver Circuit ........ 4-1
Vertical Main Amplifier ......... 4-1
Trigger Signal Circuit ........... 4-1
TV Trigger Signal Separator Circuit .. 4-1
A and B Trigger Amplifier Circuits .. 4-3
A and B Sawtooth Generator Circuits 4-3
Horizontal Amplifier ........... 4-3
Z-Axis Amplifier .............. 4-3
CRT Circuit ................. 4-4
Low-Voltage Circuit ............ 4-4
4-1-12 Calibration Voltage and
Current Generator Circuit ...... 4A
SECTION 5 MAINTENANCE ___ ..••••••.••• 5-1
PREVENTIVE
MAINTENANCE ... _ . _ . __ . __ 5-1
Cleaning ..... _ . _ .. _ . . . . . . . . 5-1
If Unused for a Long Time ....... 5-1
Checking .•........ , ........ 5-2
Periodic Adjustment .. , . . . . . • .. 5-2
PARTS REPLACEMENT ........ 5-2
Cover Removal ............... 5-2
Printed Circuit Board Removal ...•. 5-2
Printed Circuit Board
Parts Replacement. . . . . . . . . . . 5-3
Replacing Resistors,
Diodes or IC's .............. 5-3
Power Transistor Replacement . ... . 5·3
CRT Replacement ............ , 5-4
High-Voltage Power
Transformer Replacement. ..... 5·5
Replacing Control Knobs
and Rotary Switches ......... 5-5
Replacing Push button Switches .... 5-5
CHECK AND ADJUSTMENT. _ ••••• 6-1
GENERAL. ................. 6-1
PERIOD OF CHECK AND
ADJUSTMENT ............... 6-1
PRECAUTIONS FOR CHECK
AND ADJUSTMENT ......... 6-1
EQUIPMENT REQUIRED ....... 6-1
CHECK AND ADJUSTMENT ITEMS 6-4
PREPARATION .............. 6-6
POWER SUPPLY AND CRT
CHECK AND ADJUSTMENT ... 6-6
Power Supply DC Level I
(Voltage Range) ............ 6-6
Power Supply DC Level 11
(Ripple Voltage) ............ 6-7
AC Line Voltage Range ......... 6-B
Limiter Level ................ 6-9
High-Voltage Power Supply ....... 6-10
Intensity ................... 6-11
Focus ..................... 6-12
The parallel of the Horizontal
Trace and the Horizontal Scale
(TRACE ROTATION) .... , ... 6-13
The Parallel of the Vertical Trace
and the Vertical Scale
(ORTHOGONARITY) ........ 6-14
Pattern Distortion. " . " .... ... .. 6·15
CALIBRATOR OUTPUT ........ 6-16
Output Voltage ............... 6-16
Repetition Rate .•..•...•..•.. 6-17
VERTICAL DEFLECTION SYSTEM6-1B
ADD Balance ................ 6-18
X 5 Balance ................. 6-19
mV Balance ................. 6-20
Variable Balance.. . .......... 6-20
Pulse Response I
(CH1. CH2 sag at 10mV/DIV) ... 6-21
Deflection Factor I (CH1. CH2) .... 6-22
Pulse Response I
(CH1. CH2 sag at 10mV/div) .... 6-24
Position Center (CH3. CH4) ...... 6-25
Attenuator Compensation I
(CH1. CH2) ............... 6-26
Attenuator Compensation 11
(CH3. CH4) ............... 6-28
Deflection Factor II
(CH3. CH4) ............... 6-30
Pulse Response III
(overshoot and others) ........ 6-31
Pulse Response IV
(CH3. CH4 sag). ............ 6-33
Bandwidth .................. 6-34
Linearity ................... 6-35
TRIGGERING SYSTEM ......... 6-36
F I X triggering level ............ 6-36
Triggering Level I
(CH1. CH2) ............... 6-38
Triggering Level II
(CH3. CH4) ............... 6-40
HORIZONTAL DEFLECTION
SYSTEM ................. 6-42
Average Voltage
Horizontal Amplifier ......... 6-42
Magnification Center .. ......... . 6·42
A.B Sweep Start .............. 6-43
Iwatsu-6698-Manual-Page-1-Picture
Kostenlos herunterladen


Kommentare

Noch keine Kommentare vorhanden.

Kommentar Hinzufügen

* Pflichtfeld
(wird nicht veröffentlicht)
 
Bold Italic Underline Strike Superscript Subscript Quote Line Bullet Link Email Image Video
 
Smile Sad Huh Laugh Mad Tongue Crying Grin Wink Scared Cool Sleep Blush Unsure Shocked
 
1000
Enter the third word of this sentence.
 
Die Antwort lautet:
 
Informiere mich via E-Mail über neue Kommentare.
 
Meine Daten auf diesem Computer.
 
 
Powered by Commentics