Geräte Informationen:

Keithley 7999-6 Interface
Hersteller:
Keithley
Modell: 7999-6
Datum: 2001
Kategorie: Messgeräte
Gruppe: Interface
Beschreibung: GPIB RF Relay Unit
Informationen:
                                    The Model 7999-6 is an IEEE-488 controlled, single or dual, 4 or 6 pole, 19-inch rack
mounted relay unit. Additional features of the Model 7999-6 are as follows:
• N-type bulkhead connectors (insulated)
• +24VDC power connections
• LED indicators for error, power, and relay status
• Operating range to 4GHz (relay dependent)
• Can be upgraded from 4-pole to 6-pole relays

Folgende Anleitungen sind hier verfügbar:

Keithley -- 7999-6 -- Service- und Bedienungsanleitung
Dateiname: Keithley-5543-Manual-Page-1-Picture
Dokumenttyp: Service- und Bedienungsanleitung
Seitenanzahl: 87
Dateigröße: 1.40 Mbytes (1465105 Bytes)
Sprache: Englisch
Revision: A
Dokument-ID/Nummer: 7999-6-901-01
Datum: April 2001
Qualität: Elektronisches Dokument, kein Scan, sehr gut lesbar.
Upload Datum:
MD5: eda9430778a16daf86eaac26278b6410
Downloads: 104 seit dem 02 März 2014
Informationen:
1 General Information
Introduction
................................................................................
1-2
Feature overview
........................................................................
1-2
Warranty information
.................................................................
1-2
Manual addenda
.........................................................................
1-2
Safety symbols and terms
.......................................................... 1-3
Specifications
.............................................................................
1-3
Unpacking and inspection
.......................................................... 1-3
Inspection for damage
......................................................... 1-3
Handling precautions
.......................................................... 1-3
Shipment contents
...............................................................
1-4
Instruction manual
..............................................................
1-4
Repacking for shipment
...................................................... 1-4
Connections
................................................................................
1-4
2 Connections
Introduction
................................................................................
2-2
Handling precautions
.................................................................
2-2
Configuration
.............................................................................
2-2
Layout
.................................................................................
2-2
Simplified schematic
........................................................... 2-4
Connections
................................................................................
2-5
GPIB control connection
..................................................... 2-5
Power connector
..................................................................
2-8
3 Operation
Introduction
................................................................................
3-2
Maximum signal considerations
................................................ 3-2
Bus operation (GPIB)
.................................................................
3-3
Bus connections
..................................................................
3-3
Primary address
...................................................................
3-3
Programming syntax
........................................................... 3-3
Response messages
............................................................. 3-7
Status model
...............................................................................
3-8
Event register sets
............................................................. 3-10
Enable registers
.................................................................
3-11
Queues
...............................................................................
3-11
Status byte and SRQ
......................................................... 3-13
Service request enable register
.......................................... 3-14
Serial polling and SRQ
..................................................... 3-15
Clearing registers and queues
................................................... 3-16
Programming enable registers
.................................................. 3-17
Reading registers
...............................................................
3-17
Common commands
.................................................................
3-18
GPIB commands
.......................................................................
3-26
ROUTe commands
............................................................
3-26
:CLOSe...............................................................................
3-28
:CONFigure........................................................................
3-29
STATus commands
............................................................
3-30
:QUEue...............................................................................
3-30
SYSTem commands
.......................................................... 3-32
Manual operation
......................................................................
3-34
Switching considerations
.......................................................... 3-35
Connector integrity
............................................................
3-35
Voltage Standing Wave Ratio
............................................ 3-35
Path isolation
.....................................................................
3-36
Insertion loss
.....................................................................
3-36
RFI/EMI
............................................................................
3-36
Errors
........................................................................................
3-37
4 Service Information
Introduction
................................................................................
4-2
Handling and cleaning precautions
............................................ 4-2
Handling precautions
........................................................... 4-2
Card and connector cleaning
............................................... 4-2
Performance verification
............................................................. 4-3
Environmental conditions
.................................................... 4-3
Recommended equipment
................................................... 4-3
Channel resistance tests
....................................................... 4-3
Replacing components
................................................................
4-4
Replacement parts
...............................................................
4-4
Replacement precautions
..................................................... 4-5
Soldering considerations
..................................................... 4-5
Relay replacement
...............................................................
4-5
Circuit board removal
.......................................................... 4-8
GPIB address
..............................................................................
4-8
5 Replaceable Parts
Introduction
................................................................................
5-2
Parts list
......................................................................................
5-2
Ordering information
..................................................................
5-2
Factory service
............................................................................
5-2
Component layout
......................................................................
5-2
Keithley-5543-Manual-Page-1-Picture
Kostenlos herunterladen


Comments (0)

No comments yet. Be the first!

Add Comment

* Required information
1000
Enter the fifth word of this sentence.
Powered by Commentics